Video Processor, Scaler, Switcher, Integrated TV Tunerwith Hi-Resolution Picture-in-PictureTVP-1000Installation andOperationsManual205 Commercial Cour
8.0 On Screen Display (OSD)1. The On Screen Display is activated with the “Menu” button.2. The OSD is removed if the “Menu” key is again pressed.3. Pr
On Screen Display (continued)8.2.2 BRIGHTNESSActivates slider to adjust picture brightness.8.2.3 SATURATIONActivates slider to adjust color saturation
-10-On Screen Display (continued)8.3.6 V POSITIONActivates slider to adjust vertical position.For PiP channel signal source, move “ ” down and press “
-11-On Screen Display (continued)8.4.3 MAIN FORMATAllows the user to manually override the auto input detection. The firmware detects the input format
-12-On Screen Display (continued)8.5 DISPLAY SETUPThe display setup menu contains the sub-menu for output display timing and display format selection.
On Screen Display (continued)8.6.3 SOURCE / COUNTRY (PAL / SECAM Version)There are three choices for TV sources: BCST (broadcast), CATV(cable), IRC an
On Screen Display (continued)8.7.1.2 TILE MODEThe tile mode allows the user to see multiple PiP windows. The most common way to use tile mode is TV ch
On Screen Display (continued)8.9 MISCELLANEOUS8.9.1 FILM MODEThe film detection switches between VT, AFM, GFX, and SM automatically. This selection al
-16-9.0 SpecificationsSupported Video Input TimingInput Format Horiz. Freq. Vertical Freq. Active Resolution Total Pixel Clock(KHz) (Hz) (Pixels x Lin
10.010.1 RS-232 ProtocolControl PortRS232 -Contact Closure -Pins 1,3,5 Note: Pin 2 must be disabled with jumper J9 removed (factory default)Pins 1,2,4
Table of ContentsProduct Description ...1Warning ... 2Unpacking ...
-18-10.1 (Continued)RS-232 Protocol!KEY_MVID<CR> Video to Main!KEY_MSVID<CR> SVideo to Main!KEY_MRGB<CR> RGB to Main!KEY_MYPBPR<C
-19-10.1 (Continued)RS-232 ProtocolCharacter Generator Commands?PIN<CR> PiP Input Query responds with ~PVID<CR> or ~PSVID<CR> or ~PT
-20-10.1 (Continued)RS-232 ProtocolGeneral InfoTips:The above is to show the display area (grey) with the text Hello World in Green. The white outline
-21-11.0 Connector SpecificationsCONTROLRGB/YPbPrRS232 -Contact Closure -15 Pin VESA VGA ConnectorPins 1,3,5 Note: Pin 2 must be disabled with jumper
12.0Random noise in video imageWhite noiseHum on all channelsGhostingImage is always greenImage does not fit screenComputer image jittersComputer sign
13.0 Frequently Asked QuestionsIt is generally a good idea to make certain the latest firmware from the Aurora site is loaded into the unit. Tofind ou
13.0 ContinuedFrequently Asked QuestionsQ: I can not get an image out of my Satellite receiver.A: Some receivers output 1080i and 720p as RGBHV. The c
14.0 Upgrading FirmwareWhat to do if flash upgrade fails or is interrupted:1) Download latest copy of Flash123 from www.auroramultimedia.com under the
Limited Lifetime WarrantyAurora Multimedia Corp. (“Manufacturer”) warrants that this product is free of defects in both materials andworkmanship for t
FCC Part 15 StatementCE Declaration of ConformityRADIO AND TELEVISION INTERFERENCEThis equipment has been tested and found to comply with the limits f
1.0 Product DescriptionThe TVP-1000 is an integrated Scaler, TV Tuner, and Switcher capable of Hi-Res PiP. The TVP-1000 provides enhanced functionalit
4.0 InstallationBefore the TVP-1000 board is installed into the Pioneer plasma, the following must be setup:1) With the Plasma power off (use main pow
Video/S-Video Input(DVD, VCR, etc.)RGB / YPbPr Input(Computer, Component Sources, etc.)Antenna Input(Cable TV, etc.)For RS-232 Control use theprovided
5.0 Pioneer Plasma Setup1) Turn the main power switch located underneath the plasma on. The Plasma should be in standby (Solid Red LED onFront). With
6.0 System OverviewThe vast amount of features in the TVP-1000 can seem overwhelming at first. As you will see it is pretty easy to catch ononce expla
7.0 Remote ControlUsing the Aurora IRC-1a 47 Button Remote-6-The Aurora remote has the ability to control the TVP-1000 and thePioneer plasma. There ar
7.0 (continued)Remote ControlNote: TVP-1000 functions will operate only when TVP-1000 button is pressed. Plasma functionswill operate only when Plamsa
Commentaires sur ces manuels